SOFTER — STRONGER — SMARTER
Find the right suspension parts.
Honda CR-V Control arm bushings are the polyurethane bushing kits used to replace worn rubber bushings at the inner and outer pivot positions of the front and rear control arms. Every control arm connects the wheel hub carrier to the chassis through at least two inner pivot bushings and, on applicable designs, an outer bushing at the ball joint ... Read more
Honda CR-V Control arm bushings are the polyurethane bushing kits used to replace worn rubber bushings at the inner and outer pivot positions of the front and rear control arms. Every control arm connects the wheel hub carrier to the chassis through at least two inner pivot bushings and, on applicable designs, an outer bushing at the ball joint housing or arm-to-knuckle interface. The condition of these bushings at every position directly determines how precisely the wheel is located through its travel arc, how consistently the vehicle holds its alignment geometry under dynamic load, and how much of the road and drivetrain inputs at the wheel are transmitted into the chassis as NVH.
Control arm bushing wear is the primary driver of gradual alignment drift, tire wear inconsistency, handling imprecision and front or rear end NVH on high-mileage vehicles across every platform type. As inner bushings deteriorate, the arm pivots with increasing compliance, allowing geometry to shift under braking, acceleration and cornering loads in ways that cannot be corrected through alignment adjustment alone until the bushings are renewed. The control arm bushings range covers Vehicle Master Bushing Kits, Essential and Enhancement Kits, front lower control arm inner forward and rearward individual position kits, front upper inner bushing kits, front upper and lower combined sets for RWD and 4WD, rear control arm bushing sets and individual position kits, geometry correction variants for caster, camber, anti-lift and toe, rear control arm bushing inserts, MAX C universal dimensionally specified bushings, performance inner bushing kits, and commercial truck control arm bushings. Most products are backed by a limited lifetime warranty. Installation guides are available across most products.
Control arm bushing wear accumulates progressively across every inner and outer pivot position on the arm. Each bushing that exceeds its designed compliance contributes to a slightly less precise wheel location that compounds with every other worn bushing in the system. The result is a gradual but accelerating degradation in alignment retention, steering response and handling predictability that worsens with every mile and cannot be corrected by alignment adjustment, shock absorber replacement or tire rotation while the bushings remain worn.
On geometry correction variants, a worn Honda CR-V inner bushing that has allowed the arm to move beyond its designed arc can introduce caster, camber or anti-lift geometry errors that a standard replacement bushing cannot address. Geometry correction bushing kits at the inner forward or rearward position introduce a controlled offset that simultaneously renews the bushing and corrects the geometry error in a single installation, restoring both compliance and the correct alignment angle from the same service.
The Honda CR-V control arm bushing range includes:
Control arm bushing renewal is the most direct and structurally complete suspension repair available for addressing the alignment drift, handling degradation and NVH that high-mileage and heavily used vehicles accumulate at the inner pivot level. Renewing the bushings restores correct arm compliance at every renewed position, eliminates the geometry inconsistency that worn inner pivots allow under dynamic load, and returns the front and rear suspension to the correct operating baseline from which every other component on the vehicle performs as designed.
Honda CR-V Vehicle Master Kits deliver the most complete renewal across the full vehicle in a single purchase, eliminating the compounding effect of multiple worn bushing positions simultaneously. Individual and combined position kits provide targeted renewal at specific arms and positions identified through inspection or alignment diagnosis, allowing the correct level of renewal to be matched to the actual condition of the vehicle without requiring full vehicle service. Geometry correction variants address both bushing wear and geometry error in a single installation, delivering correct compliance and correct alignment angles from the same service rather than requiring separate bushing replacement and alignment correction hardware.
Honda CR-V Control arm bushing kits are designed for installation at the inner and outer pivot positions of the front and rear control arms on applicable platforms. Installation times range from under an hour for individual position kits and insert renewals to over six hours for full vehicle master kit installations depending on the platform and number of positions covered. Installation guides are available across most products. For additional technical assistance, a dedicated support team is available to confirm correct product selection, geometry correction specification and fitment for the specific vehicle, drivetrain configuration and suspension design.
Honda CR-V Control arm bushings are manufactured from high-strength polyurethane engineered to withstand the sustained pivot loads, road shock, vibration and environmental exposure that front and rear control arm inner and outer positions are subject to in everyday, performance, towing and off-road use. Geometry correction bushing variants are precision machined to deliver the specific caster, camber, anti-lift or toe correction required for the applicable platform and position. Rear control arm bushing inserts deliver polyurethane compliance at the inner bushing interface without requiring shell removal, reducing installation complexity on applicable platforms. Most products are backed by a limited lifetime warranty.
Honda CR-V Control arm bushings are a practical solution for:
The right control arm bushing kit restores correct compliance and geometry at every renewed arm position, eliminates alignment drift and NVH from worn inner pivots, and delivers a suspension system that holds its geometry and performs precisely under every driving condition.
Explore the full Honda CR-V control arm bushings range and find the right kit for your vehicle. With Vehicle Master Bushing Kits, Essential and Enhancement Kits, front lower inner forward and rearward bushing kits in standard and geometry correction variants, front upper inner bushing kits, front upper and lower combined sets for RWD and 4WD, rear control arm bushing sets and inserts, geometry correction variants for caster, camber, anti-lift and toe, MAX C universal bushings, performance inner bushing kits and commercial truck control arm bushings across a broad range of applicable platforms, you can renew every control arm bushing position accurately and complete every suspension service with confidence.
Qty Required 1 |
|---|
Qty Required 1 |
|---|
Qty Required 1 |
|---|
Qty Required 1 |
|---|
Tell us what you were trying to find so we can improve the site.
Give FeedbackMicrosoft Internet explorer is at the end of its life and is no longer supported, this poses a security risk. As such the Fulcrum website does not support Internet Explorer.
If you are using Internet Explorer to browse this website, you may get unexpected errors when viewing pages or purchasing products through our checkout.
Please use Google Chrome, Mozilla Firefox or Microsoft Edge.
US
Australia
United Kingdom
Europe